2311.gif

Screw Shield For Arduino - Ultimate Guide(Helpful)

Screw Shield For Arduino - Ultimate Guide(Helpful)

Abstract

A screw shield is used to extend and transform the sides of Arduino and Arduino variants into screw nature terminal blocks. Usually, the wing-like screw shield is composed of 18 terminals on its pin side where 16 are normal while 2 are the extra GND terminals. Following are the few of the salient features of screw shield.

 

screw shield1_0.png

 

Content

1. Salient Features of a Screw Shield

2. Machines Required in the Construction of Screw Shield

3. Components Required for Construction

4. Step by Step Instructions about Making a Screw Shield

5. Making of a Screw Shield

6. Soldering the Shield

7. Shaping the Screw Shield

8. Few Important Tips

 

1. Salient Features of a Screw Shield

 

  1.1.A screw shield is compatible with Arduino and Arduino variants

  1.2.Consists of SPI extension border

  1.3.Completely stackable

 

2. Machines Required in the Construction of Screw Shield

 

  2.1.Soldering Iron

  2.2.Drill machine

  2.3.A hacksaw

 

3. Components Required for Construction

 

  3.1.An Arduino Pro Mini is the integral part required for Screw Shield

  3.2.24 Headers (Female)

  3.3.A stripe board

  3.4.24 Screw Terminals with 2.54 mm pitch

  3.5.Solder

 

screw shield2.png

 

4. Step by Step Instructions about Making a Screw Shield

 

  Few Points to be kept under Consideration before Making the Screw Shield

  4.1.You should take a stripboard which resembles much like a breadboard having strips along one side going towards the other,

  4.2.Take the pins and fuse them into the striped board with the help of copper rails plugged in from beneath,

  4.3.These copper rails will help in transmitting electric current to all the components joined to the stripboard,

  4.4.Now connect the connect screw terminals of 2.54 mm pitch to each pinhole without making a gap that is a perfect setup for an Arduino Pro Mini,

  4.5.Avoid connecting programming pins to anything because these will only be used for programming purpose through FTDI.

 

screw shield3.png

 

5. Making of a Screw Shield

 

Cut a couple of female headers and take 12 female pins for each side. Connect the 12 screw terminals and join each pin with a separated rail. Take the female headers to the female pins on your Pro Mini in such a way that they can be easily positioned. Set these positioned female headers adjacent to the screw terminals fixed on the board. If there are any remaining screw terminals, locate them on the other side of the board. This is the final composition which now requires soldering. Let us have a deeper look at this essential step.

 

6. Soldering the Shield

 

Though it seems complicated but actually it is a very simple part of the whole procedure. All you have to do is just to put the board upside down and get started with fixing the screw terminals and female pins to the board. The actual way of doing this fixing is to connect the first and the last one together as it will give you a perfectly assembled and secure board.

Making the connection of bins to the board will heat up and can easily connect to the solder. Now comes the cutting and finalizing the assembling procedure.

 

7. Shaping the Screw Shield

 

Now shape and cut the screw shield according to your requirement and keep the remaining piece for future use in any other prototyping project. You can use a hacksaw for this purpose.

 

Important Tip

Cutting the screw shield closer to the edges of female headers and screw terminals will be perfect. I will recommend cutting the shield between columns of pinholes to avoid any kind of damage.

 

 

8. Few Important Tips

 

Make a breaking hole between both sides of connection just to avoid any kind of mishap the connection between both sides is broken with the help of 2mm drill bit. Dig into the pinhole to secure the screw shield from any kind of breakage in the Pro Mini board.

 

screw shield4.png

 

Remove all kind of copper around the pinhole by drilling into each of them between each female header. Thus drilling will distort the connection between two sides and make 24 individual connections.

 

Here we go, your Pro Mini screw shield is ready to use, enjoy the most secured and reliable connections with your own handmade screw shield.

 

WellPCB

 

Regardless if you're a starter or a seasoned guy in the subject of PCB manufacturing, PCB Manufacturing in China is a smart choice. Probably most attractive features are that PCB Manufacturers in China have the ability to ship worldwide, with an alternative to pick a shipping agent of your own preference. Nearly all PCB Manufacturers in China will provide you the lowest prices, even as compared with your regional manufacturer. WellPCB is among the leading PCB Manufacturers in China. 

They have the ability to manufacture any dimension of your PCB Design in large or small scale order. To make an order, you're only required to proceed to WellPCB and introduce the design of the PCB Gerber documents. Additionally to creating custom PCBs as stated in your purchase, WellPCB will supply you with an option to permit them do a PCB Assembly for you at an extra cost. They also perform tests to make sure you obtain a complete product which works.